HeatCoolHQ heatcoolhq.com (888) 217-3739

Kirby, TX

Furnace and Heating Repair in Kirby, TX

Furnace repair in Kirby, TX begins with what the system does when the thermostat calls for heat, and where in that sequence it quits. Kirby has, on average, 22 days a year with a low of 32°F or colder and about one at 20°F or colder (NOAA 1991–2020 normals, station 5 miles away). Half the homes in Kirby were built before 1977 (Census ACS 2019–2023). When the gas utility finds a leak or an unsafe furnace it shuts the gas off and tags the appliance, and only a repair brings the gas back.

(888) 217-3739

Texas contractors. No obligation for the call.

The year in Kirby—cooling runs nearly all year
The year in Kirby. cooling runs nearly all year. There is no month when both systems are idle. JFMAMJJASOND
heatingcooling22 days below freezing · July dew point 70°F
A technician with a meter at the open panel of a gas furnace
A meter at the burner assembly with the panel off. The ignition sequence runs in a fixed order, and the step where it stops is what names the part.

No heat on a cold night comes down to a short list of faults, and the step where the sequence stops names the part. Say what heats the house, both thermostat numbers — the setting and the reading — and what the equipment is doing, and a heating contractor who covers Kirby takes it from there.

In Kirby the heating half of the system is the part nobody thinks about, and in a climate like this it is as often as not the same outdoor unit that cools in July, running the other way. People live with a heat pump for years without knowing the machine does both jobs, which is why the first thing worth saying on the phone is which of the two heats the house.

Air from the vents that feels cool in winter is not a fault by itself — a heat pump works on a smaller difference between the room and the air it supplies, and it runs longer cycles to make that up. The test is whether the room gets to the number on the thermostat, and whether the electric strips are doing work the heat pump should be doing: a thermostat set or wired wrong brings them on when the weather never asked for them.

Where July dew points sit at 70°F and above, the indoor coil runs wet for the whole season, and everything it takes out of the air leaves through one drain line. A summer of that grows a film inside the trap and the line, and nobody thinks about a drain on the first cold night: a condensing furnace makes water of its own, in most installations it goes down that same line, and a line that will not take it backs the water up until the pressure switch refuses to close. So a no-heat call in a climate like this can end at the drain rather than at the burner.

Kirby, TX in numbers

Days a year with a low of 32°F or colder22NOAA 1991–2020 normals, station 5 miles away
Days a year with a low of 20°F or colder1NOAA 1991–2020 normals
Average July dew point70°FPRISM 1991–2020 normals
Median year homes were built1977Census ACS 2019–2023
Households2,912Census ACS 2019–2023
CountyBexar CountyCensus Bureau
Federal minimum for a new split central AC14.3 SEER2 under 45,000 Btu/h (Southeast)DOE, 2023 standard

What the store-bought fix actually does

A new filter is the one thing off a hardware-store shelf that ends a no-heat call outright, and it is fair to say so: a filter that has loaded up chokes the return, the heat exchanger cannot put its heat into air that is barely moving, the limit switch opens, and the furnace shuts itself down and short cycles. What a new filter cannot do is prove it was the fault. Where the furnace locks out again within a day of a new one going in, the air was restricted somewhere past the filter, and a technician measures the temperature rise across the furnace to find where.

A heating tune-up before the season

What a technician checks on a heating maintenance visit is concrete, and worth naming on the phone: the ignition sequence run from start to finish, the flame sensor cleaned and its signal read, the temperature rise measured across the furnace, the heat exchanger looked over for cracks, carbon monoxide checked at the flue, and the drain cleared. On a heat pump the list adds the defrost cycle and the auxiliary heat strips; on a boiler, the pressure, the relief valve and the circulator.

A technician at an indoor air handler

When to stop and call in Kirby

  • The furnace locks out again within an hour of being reset.
  • There is a tag on the furnace and the gas supply has been shut off.
  • The blower runs and the air never warms, or the thermostat is asking for heat while the reading keeps dropping.
The figure
Set by the contractor and said before the work starts. This site never quotes and has no part in it. If a technician cannot say what the visit covers before beginning, that is the moment to stop.
The call
Describing what the system is doing commits you to nothing. Nothing is booked until you say so.
Coverage
By town, not by region. Kirby and the towns around it, and it shifts with who is taking calls at the hour you ring.

What a visit in Kirby involves

  1. 01

    The diagnosis

    At the thermostat first, then at the furnace or the condenser, in the order the equipment runs. What the system is doing is established before any part is named.

  2. 02

    The repair

    Agreed with the contractor before it starts. Where a part has to be ordered, a technician says so rather than leaving the system apart.

  3. 03

    What happens after

    A system that failed once in a season often fails again in it. Whether that is the same fault or a second one is worth asking while the technician is still there.

What to have ready when you call from Kirby

  1. 01Which system it is: a furnace, a boiler with radiators or baseboard, or a heat pump with electric backup.
  2. 02Both numbers from the thermostat — the setting, and what it says the room is — and whether the screen is blank, because a thermostat wired without a common wire runs off its battery, and a battery that has gone down looks exactly like a dead furnace.
  3. 03Whether the gas utility has already been to the house, and whether there is a tag on the appliance.

Leave the reset alone while you wait — each press relights a furnace that shut itself down for a reason, and the lockout it is holding is the first thing a technician reads.

Heating Repair in Kirby: questions

How cold does Kirby get in winter?

Kirby averages 22 days a year with a low of 32°F or colder and 1 at 20°F or colder, by the 1991–2020 climate normals for a NOAA station 5 miles away. Heating is rarely asked for here, so a fault in it can sit unnoticed until the one cold week of the year.

How old are the homes in Kirby?

Half the homes in Kirby were built before 1977, by the Census Bureau's 2019–2023 American Community Survey. Detached houses make up most of the housing. Equipment in houses of that age is often on its second set, and the install date on the label decides whether parts are still made. Manufactured homes are common enough here that a packaged unit outside, feeding a duct under the floor, is worth mentioning on the call.

What efficiency does a new gas furnace in Kirby need?

The federal minimum for a new non-weatherized gas furnace is an AFUE of 80. A 95 standard is set for furnaces made after December 18, 2028 and is still in court, so a furnace going in now can be an 80 or a condensing model in the 90s.

Map loads when you reach it

Other services in Kirby

Heating Repair nearby

Call (888) 217-3739