HeatCoolHQ heatcoolhq.com (888) 217-3739

Murray, UT

Furnace and Heating Repair in Murray, UT

Furnace and heating repair in Murray, UT starts at the thermostat and follows the equipment through its start-up sequence to the step where it stops. Murray has, on average, 112 days a year with a low of 32°F or colder and 33 at 20°F or colder (NOAA 1991–2020 normals, station 6 miles away). Half the homes in Murray were built before 1978 (Census ACS 2019–2023). When the gas utility finds a leak or an unsafe furnace it shuts the gas off and tags the appliance, and only a repair brings the gas back.

(888) 217-3739

Utah contractors. No obligation for the call.

The year in Murray—both systems work a real season
The year in Murray. both systems work a real season. There is no month when both systems are idle. BELOW FREEZINGJFMAMJJASOND
heatingcoolingbelow freezing112 days below freezing · July dew point 45°F
A technician with a meter at the open panel of a gas furnace
A meter at the burner assembly with the panel off. The ignition sequence runs in a fixed order, and the step where it stops is what names the part.

No heat on a cold night comes down to a short list of faults, and the step where the sequence stops names the part. Say what heats the house, both thermostat numbers — the setting and the reading — and what the equipment is doing, and a heating contractor who covers Murray takes it from there.

The list of faults is short: flame sensor, ignitor, pressure switch, limit switch, a filter starving the blower, a thermostat that lost its common wire. What separates them is the order the equipment runs in — the inducer spins up first, the pressure switch proves it, the ignitor glows, the gas valve opens, and the flame has to prove itself within seconds. A technician follows that order at the appliance, and the call is what puts one in front of it.

The thing to watch in a climate like this is that the two systems usually went in together. A furnace and the AC that came with it reach the end of their service lives together, and the same fault on a system installed in 2009 opens a different conversation than it does on one installed in 2019. A technician answers that at the appliance, before a part is ordered.

Where the heat comes from a heat pump, a cold snap hands the work to its auxiliary heat strips — resistance heat, which a heat pump calls in below about 35°F, and a cold week spent on the strips turns up on the electric bill. The reason it turns into a repair question is that the strips can hide a fault: a heat pump that has stopped heating still leaves a warm house, because the strips take the whole load and the thermostat never complains. Often the first sign is the bill rather than the cold, and by then the system has been running the expensive half of itself for weeks.

Murray, UT in numbers

Days a year with a low of 32°F or colder112NOAA 1991–2020 normals, station 6 miles away
Days a year with a low of 20°F or colder33NOAA 1991–2020 normals
Average July dew point45°FPRISM 1991–2020 normals
Median year homes were built1978Census ACS 2019–2023
Households20,401Census ACS 2019–2023
CountySalt Lake CountyCensus Bureau
Federal minimum for a new split central AC13.4 SEER2 (North region)DOE, 2023 standard

Why heating faults do not fix themselves

A furnace that has to be reset to keep running is not a furnace that is working. Each lockout is a control board refusing to try again after a safety did not prove — the flame, the pressure switch or the limit — and a reset answers none of that. What a reset does change is the wear: a furnace short cycling through a cold week runs its ignition sequence dozens of times a day, and the ignitor and the inducer motor are the parts paying for it.

A heating tune-up before the season

What a technician checks on a heating maintenance visit is concrete, and worth naming on the phone: the ignition sequence run from start to finish, the flame sensor cleaned and its signal read, the temperature rise measured across the furnace, the heat exchanger looked over for cracks, carbon monoxide checked at the flue, and the drain cleared. On a heat pump the list adds the defrost cycle and the auxiliary heat strips; on a boiler, the pressure, the relief valve and the circulator.

A technician at an indoor air handler

Signs it is time to call

  • The furnace locks out again within an hour of being reset.
  • There is a smell of gas, or a carbon monoxide alarm has gone off — outside first, then the gas utility, then the repair call.
  • There is a tag on the furnace and the gas supply has been shut off.
The license
Held by the contractor, not by this site, and issued where the work happens — Utah licenses at state level, at city level or not at all depending on the trade and the town. Ask for the number and the name it is held under: a trading name and the licensed entity are often not the same.
The call
Describing what the system is doing commits you to nothing. Nothing is booked until you say so.
Coverage
By town, not by region. Murray and the towns around it, and it shifts with who is taking calls at the hour you ring.

What happens on the visit

  1. 01

    The diagnosis

    At the thermostat first, then at the furnace or the condenser, in the order the equipment runs. What the system is doing is established before any part is named.

  2. 02

    The finding, out loud

    What failed, whether it is the fault or a symptom of another one, and whether the repair suits the age of the system. A diagnostic visit is usually charged separately from the repair — ask whether it is credited if the work goes ahead, because that differs from one contractor to the next.

  3. 03

    What happens after

    A system that failed once in a season often fails again in it. Whether that is the same fault or a second one is worth asking while the technician is still there.

What to have ready when you call from Murray

  1. 01Which system it is: a furnace, a boiler with radiators or baseboard, or a heat pump with electric backup.
  2. 02What it is doing: silent, clicking and stopping, lighting and dropping out, or running with cold air at the vents.
  3. 03Whether the gas utility has already sent someone, and whether anything has been tagged.

Leave the reset alone while you wait — each press relights a furnace that shut itself down for a reason, and the lockout it is holding is the first thing a technician reads.

Heating Repair in Murray: questions

How many freezing days does Murray have?

Murray averages 112 days a year with a low of 32°F or colder and 33 at 20°F or colder, by the 1991–2020 climate normals for a NOAA station 6 miles away. Both halves of the system work hard here, and the heating side runs for months rather than weeks.

How old are the homes in Murray?

Half the homes in Murray were built before 1978, by the Census Bureau's 2019–2023 American Community Survey. Detached houses make up about half of the housing. Equipment in houses of that age is often on its second set, and the install date on the label decides whether parts are still made.

How efficient must a new gas furnace be?

A new non-weatherized gas furnace has to reach an AFUE of at least 80 under the federal minimum. DOE has set 95 for furnaces made after December 18, 2028, and that rule is still being fought in court, so a furnace installed now can still be an 80 or a condensing 90-plus.

Map loads when you reach it

Other services in Murray

Heating Repair nearby

Call (888) 217-3739