HeatCoolHQ heatcoolhq.com (888) 217-3739

Dallas, TX

Heat Pump Repair and Replacement in Dallas, TX

Heat pump repair in Dallas, TX starts by telling a normal defrost cycle or auxiliary-heat run from one that is a fault. Dallas has, on average, 23 days a year with a low of 32°F or colder and 2 at 20°F or colder (NOAA 1991–2020 normals, station 7 miles away). Half the homes in Dallas were built before 1980 (Census ACS 2019–2023). Every split heat pump made since January 1, 2023 has to rate at least 14.3 SEER2 for cooling and 7.5 HSPF2 for heating, the same federal minimum in every state.

(888) 217-3739

Texas contractors. No obligation for the call.

The year in Dallas—cooling runs nearly all year
The year in Dallas. cooling runs nearly all year. There is no month when both systems are idle. JFMAMJJASOND
heatingcooling23 days below freezing · July dew point 68°F
A technician checking the coil of an outdoor heat pump in winter
The top grille off, frost across the coil. A heat pump melts that off on a schedule of its own, which looks like a fault and is not.

Air that feels cool at the vents in winter is usually the heat pump working as designed, and a heat pump that sits on auxiliary heat for hours in mild weather usually is not. Say what the thermostat reads and a heating and cooling contractor can come out to Dallas and tell the two apart.

A heat pump in Dallas spends the year on the cooling side, and the heating side is a handful of mornings. What a no-heat call means here depends on what else is in the house: where there is a furnace, the heat pump has something to hand the load to, and where there is none — and in this climate plenty of houses have none — the only thing behind it is a bank of electric resistance strips. That is the first thing a technician asks about, because there is no second appliance to switch to.

Sizing here runs the opposite way from a cold climate: the cooling load sets the size, exactly as it would for an air conditioner, because it is the load that exists for most of the year — which is correct, and it also means that on the handful of genuinely cold mornings the machine runs without stopping and the strips carry what it cannot. A machine running continuously on a cold morning is doing its job, not failing at it.

Frost on the outdoor coil comes out of the air rather than off the ground, which is why the heaviest of it here arrives in weather nobody would call severe. A coil running below freezing takes moisture out of damp air faster than out of cold dry air, so a drizzly morning near 35°F puts more ice on it than a clear night at 15°F does — and a defrost cycle on a mild wet morning is the machine keeping up rather than falling behind. Ice still sitting there at the end of the day is the fault version, and it does not clear itself.

Dallas, TX in numbers

Days a year with a low of 32°F or colder23NOAA 1991–2020 normals, station 7 miles away
Days a year with a low of 20°F or colder2NOAA 1991–2020 normals
Average July dew point68°FPRISM 1991–2020 normals
Median year homes were built1980Census ACS 2019–2023
Households528,038Census ACS 2019–2023
CountyDallas CountyCensus Bureau
Federal minimum for a new split central AC14.3 SEER2 under 45,000 Btu/h (Southeast)DOE, 2023 standard

Why heat pumps do not fix themselves

The parts that cycle fail first, and they rarely fail alone. A run capacitor that has lost capacitance does not shut the compressor down — it raises the current the compressor draws every minute it runs, and the heat that comes with it. A heat pump asks for that on the heating side as well as the cooling one, where an AC only ever runs to cool, so the part that fails at the end of it is not the capacitor. A capacitor is a part; a compressor is a large fraction of the machine, and on a system installed before 2010 that is where the conversation turns to replacement.

A technician at an indoor air handler

Signs it is time to call

  • The thermostat sits on auxiliary or emergency heat for hours while it is mild outside.
  • It cools in summer but will not heat, or it heats but will not cool.
  • Refrigerant was added in an earlier season and the system is behaving the same way again.
The license
Held by the contractor, not by this site, and issued where the work happens — Texas licenses at state level, at city level or not at all depending on the trade and the town. Ask for the number and the name it is held under: a trading name and the licensed entity are often not the same.
The call
Describing what the system is doing commits you to nothing. Nothing is booked until you say so.
Coverage
By town, not by region. Dallas and the towns around it, and it shifts with who is taking calls at the hour you ring.

What a visit in Dallas involves

  1. 01

    The diagnosis

    At the thermostat first, then at the furnace or the condenser, in the order the equipment runs. What the system is doing is established before any part is named.

  2. 02

    The finding, out loud

    What failed, whether it is the fault or a symptom of another one, and whether the repair suits the age of the system. A diagnostic visit is usually charged separately from the repair — ask whether it is credited if the work goes ahead, because that differs from one contractor to the next.

  3. 03

    The repair

    Agreed with the contractor before it starts. Where a part has to be ordered, a technician says so rather than leaving the system apart.

What to have ready when you call from Dallas

  1. 01That the system is a heat pump, and what carries the heat when it cannot — electric, or a gas furnace on the same ducts, and not knowing is a fair answer.
  2. 02Both thermostat numbers, and whether the display is showing auxiliary or emergency heat.
  3. 03Roughly when it was installed, and what the outdoor data plate says it is charged with — R-410A on most systems in service, R-454B on recent ones.

If the house has gone cold, emergency heat is what that setting is for — say on the phone that you switched to it, because it locks out the compressor, and the fault a technician needs to watch stops happening while it is on.

Heat Pumps in Dallas: questions

How cold does Dallas get in winter?

Dallas averages 23 days a year with a low of 32°F or colder and 2 at 20°F or colder, by the 1991–2020 climate normals for a NOAA station 7 miles away. Heating is a handful of mornings here, so a heat pump spends nearly the whole year cooling.

What is the July dew point in Dallas?

The July dew point in Dallas averages 68°F, by the PRISM 1991–2020 climate normals. In air that wet an oversized air conditioner cools the house fast, shuts off before it has dried the air, and leaves rooms cool and clammy, which is why sizing starts with a load calculation for the house.

How efficient must a new heat pump in Dallas be?

The federal minimum for a split heat pump made since January 1, 2023 is 14.3 SEER2 for cooling and 7.5 HSPF2 for heating, the same in Texas as in every other state. A contractor can quote above the minimum; the rating is on the unit's label and on the AHRI certificate for the matched pair.

Map loads when you reach it

Other services in Dallas

Heat Pumps nearby

Call (888) 217-3739