Hanahan, SC
Furnace and Heating Repair in Hanahan, SC
Heating repair in Hanahan, SC comes down to finding the step where the furnace or heat pump stops in its start-up sequence. Hanahan has, on average, 22 days a year with a low of 32°F or colder and about one at 20°F or colder (NOAA 1991–2020 normals, station 3 miles away). Half the homes in Hanahan were built before 1987 (Census ACS 2019–2023). A red tag from the gas utility means it found a leak or an unsafe furnace, and the gas to it stays off until a contractor fixes the fault.
(888) 217-3739South Carolina contractors. No obligation for the call.
No heat on a cold night comes down to a short list of faults, and the step where the sequence stops names the part. Say what heats the house, both thermostat numbers — the setting and the reading — and what the equipment is doing, and a heating contractor who covers Hanahan takes it from there.
The heating half of the system is the part nobody in Hanahan thinks about, and in a climate like this it is as often as not the same outdoor unit that cools in July, running the other way. People live with a heat pump for years without knowing the machine does both jobs, which is why the first thing worth saying on the phone is which of the two heats the house.
Where a heat pump does the heating, no heat usually means it stopped heating rather than stopped running. The part that decides which job the machine is doing is the reversing valve, and one that sticks leaves an outdoor unit sounding normal and air at the registers that never warms. Where a small gas furnace does the heating instead, the list is the familiar one: flame sensor, ignitor, pressure switch, limit switch.
Where July dew points sit at 70°F and above, the indoor coil runs wet all summer, and everything it pulls out of the air leaves by one drain line. A summer of that grows a film inside the trap and the line, and nobody thinks about a drain on the first cold night: a condensing furnace makes water of its own, in most installations it goes down that same line, and a line that will not take it backs the water up until the pressure switch refuses to close. In a climate like this a no-heat call can end at the drain and never reach the burner.
Hanahan, SC in numbers
| Days a year with a low of 32°F or colder | 22 | NOAA 1991–2020 normals, station 3 miles away |
|---|---|---|
| Days a year with a low of 20°F or colder | 1 | NOAA 1991–2020 normals |
| Average July dew point | 73°F | PRISM 1991–2020 normals |
| Median year homes were built | 1987 | Census ACS 2019–2023 |
| Households | 7,866 | Census ACS 2019–2023 |
| County | Berkeley County | Census Bureau |
| Federal minimum for a new split central AC | 14.3 SEER2 under 45,000 Btu/h (Southeast) | DOE, 2023 standard |
Why heating faults in Hanahan do not fix themselves
The one fault that changes the conversation entirely is a cracked heat exchanger. It is not a repair question alone — the gas utility red-tags the appliance and shuts the supply off, and it restores the supply only after a licensed contractor has worked on the furnace. The appliance does not come back by flipping a switch, and a tag pulled off the furnace takes the record of what was found with it.
A heating tune-up before the season
A heating maintenance visit covers a concrete list, and it is worth asking about each item by name: the ignition sequence run from start to finish, the flame sensor cleaned and its signal read, the temperature rise measured across the furnace, the heat exchanger looked over for cracks, carbon monoxide checked at the flue, and the drain cleared. On a heat pump the list adds the defrost cycle and the auxiliary heat strips; on a boiler, the pressure, the relief valve and the circulator.
When to stop and call
- The furnace locks out again within an hour of being reset.
- There is a tag on the furnace and the gas supply has been shut off.
- Water is standing at the base of the furnace, or the flue outside has iced over.
- The figure
- Set by the contractor and said before the work starts. This site never quotes and has no part in it. If a technician cannot say what the visit covers before beginning, that is the moment to stop.
- The call
- Describing what the system is doing commits you to nothing. Nothing is booked until you say so.
- Coverage
- By town, not by region. Hanahan and the towns around it, and it shifts with who is taking calls at the hour you ring.
What a visit in Hanahan involves
- 01
The diagnosis
At the thermostat first, then at the furnace or the condenser, in the order the equipment runs. What the system is doing is established before any part is named.
- 02
The finding, out loud
What failed, whether it is the fault or a symptom of another one, and whether the repair suits the age of the system. A diagnostic visit is usually charged separately from the repair — ask whether it is credited if the work goes ahead, because that differs from one contractor to the next.
- 03
What happens after
A system that failed once in a season often fails again in it. Whether that is the same fault or a second one is worth asking while the technician is still there.
Before you call: what to have ready
- 01What the system is — a furnace, a boiler on radiators or baseboard, or a heat pump with electric backup.
- 02Roughly when it went in, plus the model and serial number from the data plate inside the cabinet door — the year is usually in the serial rather than printed as a date.
- 03The two thermostat numbers: the setting, and the reading it shows for the room — and whether the screen has gone blank, because a thermostat wired without a common wire runs off its battery, and a dead battery looks exactly like a dead furnace.
Leave the reset alone while you wait — each press relights a furnace that shut itself down for a reason, and the lockout it is holding is the first thing a technician reads.
Heating Repair in Hanahan: questions
How cold does Hanahan get in winter?
Hanahan averages 22 days a year with a low of 32°F or colder and 1 at 20°F or colder, by the 1991–2020 climate normals for a NOAA station 3 miles away. Heating is rarely asked for here, so a fault in it can sit unnoticed until the one cold week of the year.
When were most houses in Hanahan built?
Half the homes in Hanahan were built before 1987, by the Census Bureau's 2019–2023 American Community Survey. Detached houses make up most of the housing. Equipment in houses of that age is often on its second set, and the install date on the label decides whether parts are still made.
What efficiency does a new gas furnace in Hanahan need?
A new non-weatherized gas furnace has to reach an AFUE of at least 80 under the federal minimum. A 95 standard is set for furnaces made after December 18, 2028 and is still in court, so a furnace going in now can be an 80 or a condensing model in the 90s.
Other services in Hanahan
Heating Repair nearby