HeatCoolHQ heatcoolhq.com (888) 217-3739

Denver, CO

Furnace and Heating Repair in Denver, CO

Furnace repair in Denver, CO begins with what the system does when the thermostat calls for heat, and where in that sequence it quits. Denver has, on average, 156 days a year with a low of 32°F or colder and 62 at 20°F or colder (NOAA 1991–2020 normals, station in or next to town). Half the homes in Denver were built before 1974 (Census ACS 2019–2023). A gas utility that finds a leak or an unsafe furnace shuts off the gas and tags the appliance, and the gas stays off until a contractor repairs the fault.

(888) 217-3739

Colorado contractors. No obligation for the call.

The year in Denver—heating runs most of the year
The year in Denver. heating runs most of the year. Between the two seasons there are weeks when neither system runs, which is when a fault goes unnoticed. BELOW FREEZINGBELOW FREEZINGnothing runsJFMAMJJASOND
heatingcoolingbelow freezing156 days below freezing · July dew point 50°F
A technician with a meter at the open panel of a gas furnace
A meter at the burner assembly with the panel off. The ignition sequence runs in a fixed order, and the step where it stops is what names the part.

A system that has stopped making heat on a cold night has one of a short list of faults behind it, and the step where the sequence stops names the part. Say what heats the house, both thermostat numbers — the setting and the reading — and what the equipment is doing, and a heating contractor who covers Denver takes it from there.

Winter in Denver runs long enough that heating is the main system in the house rather than the second one, and a night without it is counted in hours rather than in inconvenience. By morning the question has moved from comfort to the pipes, which is why this is a call worth making at the hour it happens rather than in the morning.

What a winter this long changes is which part gives up first. A furnace that has been firing since October reaches January with the hours on it, so what fails is usually the part that has been working rather than the part that was weakest when it went in: an ignitor has a certain number of starts in it, an inducer motor and a blower motor turn on bearings, and a flame sensor takes on a little more of what the flame leaves behind every cycle. A cold snap adds nothing to that but the timing.

Where a heat pump does the heating, a cold snap puts it on its auxiliary heat strips — resistance heat, which a heat pump calls in below about 35°F, and a cold week spent on the strips turns up on the electric bill. The reason it turns into a repair question is that the strips can hide a fault: a heat pump that has stopped heating still leaves a warm house, because the strips take the whole load and the thermostat never complains. Often the first sign is the bill rather than the cold, and by then the system has been running the expensive half of itself for weeks.

Denver, CO in numbers

Days a year with a low of 32°F or colder156NOAA 1991–2020 normals, station in or next to town
Days a year with a low of 20°F or colder62NOAA 1991–2020 normals
Average July dew point50°FPRISM 1991–2020 normals
Median year homes were built1974Census ACS 2019–2023
Households329,578Census ACS 2019–2023
CountyDenver CountyCensus Bureau
Federal minimum for a new split central AC13.4 SEER2 (North region)DOE, 2023 standard

Before you try the store-bought fix

A new filter is the one thing off a hardware-store shelf that ends a no-heat call outright, and it is fair to say so: a filter loaded solid chokes the return, the heat exchanger cannot put its heat into air that is barely moving, the limit switch opens, and the furnace shuts itself down and short cycles. What a new filter cannot do is prove it was the fault. Where the furnace locks out again within a day of a new one going in, the air was restricted somewhere past the filter, and a technician measures the temperature rise across the furnace to find where.

A heating tune-up before the season

What a technician checks on a heating maintenance visit is concrete, and worth naming on the phone: the ignition sequence run from start to finish, the flame sensor cleaned and its signal read, the temperature rise measured across the furnace, the heat exchanger looked over for cracks, carbon monoxide checked at the flue, and the drain cleared. On a heat pump the list adds the defrost cycle and the auxiliary heat strips; on a boiler, the pressure, the relief valve and the circulator.

A technician at an indoor air handler

When to stop and call

  • The furnace locks out again within an hour of being reset.
  • There is a smell of gas, or a carbon monoxide alarm has gone off — outside first, then the gas utility, then the repair call.
  • Water is standing at the base of the furnace, or the flue outside has iced over.
The figure
Set by the contractor and said before the work starts. This site never quotes and has no part in it. If a technician cannot say what the visit covers before beginning, that is the moment to stop.
The call
Describing what the system is doing commits you to nothing. Nothing is booked until you say so.
Coverage
By town, not by region. Denver and the towns around it, and it shifts with who is taking calls at the hour you ring.

What happens on the visit

  1. 01

    The finding, out loud

    What failed, whether it is the fault or a symptom of another one, and whether the repair suits the age of the system. A diagnostic visit is usually charged separately from the repair — ask whether it is credited if the work goes ahead, because that differs from one contractor to the next.

  2. 02

    The repair

    Agreed with the contractor before it starts. Where a part has to be ordered, a technician says so rather than leaving the system apart.

  3. 03

    What happens after

    A system that failed once in a season often fails again in it. Whether that is the same fault or a second one is worth asking while the technician is still there.

What to have ready when you call from Denver

  1. 01What the system is — a furnace, a boiler on radiators or baseboard, or a heat pump with electric backup.
  2. 02What it is doing: silent, clicking and stopping, lighting and dropping out, or running with cold air at the vents.
  3. 03Whether the gas utility has already been to the house, and whether there is a tag on the appliance.

Do not keep pressing the reset while you wait — each press relights a furnace that shut itself down for a reason, and the lockout it is holding is the first thing a technician reads.

Heating Repair in Denver: questions

How many freezing days does Denver have?

Denver averages 156 days a year with a low of 32°F or colder and 62 at 20°F or colder, by the 1991–2020 climate normals for the NOAA station in or next to town. Heating is the main system here, and a furnace that quits in January is an emergency rather than an inconvenience.

When were most houses in Denver built?

Half the homes in Denver were built before 1974, by the Census Bureau's 2019–2023 American Community Survey. Detached houses make up a good share of the housing. Equipment in houses of that age is often on its second set, and the install date on the label decides whether parts are still made.

What happens if the gas company red-tags a furnace in Denver?

The gas utility red-tags a furnace when it finds a leak or an unsafe appliance, and it shuts the gas off to it. The gas stays off until a contractor repairs the fault, and a cracked heat exchanger is often where a red tag turns a repair into a replacement.

Map loads when you reach it

Other services in Denver

Call (888) 217-3739