HeatCoolHQ heatcoolhq.com (888) 217-3739

Antrim, NH

Furnace and Heating Repair in Antrim, NH

Furnace and heating repair in Antrim, NH starts at the thermostat and follows the equipment through its start-up sequence to the step where it stops. Antrim averages 172 days a year with a low of 32°F or colder and 84 at 20°F or colder (NOAA 1991–2020 normals, station 10 miles away). Half the homes in Antrim were built before 1938 (Census ACS 2019–2023), so in many of them the heating and cooling equipment has been replaced at least once while the ducts and the flue have not. A gas utility that finds a leak or an unsafe furnace shuts off the gas and tags the appliance, and the gas stays off until a contractor repairs the fault.

(888) 217-3739

New Hampshire contractors. No obligation for the call.

The year in Antrim—heating runs most of the year
The year in Antrim. heating runs most of the year. Between the two seasons there are weeks when neither system runs, which is when a fault goes unnoticed. BELOW FREEZINGBELOW FREEZINGnothing runsJFMAMJJASOND
heatingcoolingbelow freezing172 days below freezing · July dew point 59°F
A technician with a meter at the open panel of a gas furnace
A meter at the burner assembly with the panel off. The ignition sequence runs in a fixed order, and the step where it stops is what names the part.

A system that has stopped making heat on a cold night has one of a short list of faults behind it, and the step where the sequence stops names the part. Say what heats the house, what the thermostat is asking for against what it says the room is, and what the equipment is actually doing, and a heating contractor who covers Antrim takes it from there.

Winter in Antrim runs long enough that heating is the main system in the house rather than the second one, and a night without it is counted in hours rather than in inconvenience. By morning the question has moved from comfort to the pipes, which is why this is a call worth making at the hour it happens rather than in the morning.

A winter this long decides which part gives up first. A furnace that has been firing since October reaches January with the hours on it, so what fails is usually the part that has been working rather than the part that was weakest when it went in: an ignitor has a certain number of starts in it, an inducer motor and a blower motor turn on bearings, and a flame sensor takes on a little more of what the flame leaves behind every cycle. A cold snap adds nothing to that but the timing.

Where the heat comes from a heat pump, a cold snap hands the work to its auxiliary heat strips — resistance heat, which a heat pump calls in below about 35°F, and a cold week spent on the strips turns up on the electric bill. The reason it turns into a repair question is that the strips can hide a fault: a heat pump that has stopped heating still leaves a warm house, because the strips take the whole load and the thermostat never complains. Often the first sign is the bill rather than the cold, and by then the system has been running the expensive half of itself for weeks.

Antrim, NH in numbers

Days a year with a low of 32°F or colder172NOAA 1991–2020 normals, station 10 miles away
Days a year with a low of 20°F or colder84NOAA 1991–2020 normals
Average July dew point59°FPRISM 1991–2020 normals
Median year homes were built1938Census ACS 2019–2023
Households517Census ACS 2019–2023
CountyHillsborough CountyCensus Bureau
Federal minimum for a new split central AC13.4 SEER2 (North region)DOE, 2023 standard

What the hardware-store fix does and does not do

A new filter is the one item from a hardware store that ends a no-heat call outright, and it is fair to say so: a filter that has loaded up chokes the return, the heat exchanger cannot put its heat into air that is barely moving, the limit switch opens, and the furnace shuts itself down and short cycles. What a new filter cannot do is prove it was the fault. Where the furnace locks out again within a day of a new one going in, the restriction is somewhere past the filter, and a technician measures the temperature rise across the furnace to find where.

A heating tune-up before the season

A heating maintenance visit covers a concrete list, and it is worth asking about each item by name: the ignition sequence run from start to finish, the flame sensor cleaned and its signal read, the temperature rise measured across the furnace, the heat exchanger looked over for cracks, carbon monoxide checked at the flue, and the drain cleared. On a heat pump the list adds the defrost cycle and the auxiliary heat strips; on a boiler, the pressure, the relief valve and the circulator.

A technician at an indoor air handler

Signs it is time to call

  • There is a smell of gas, or a carbon monoxide alarm has gone off — outside first, then the gas utility, then the repair call.
  • There is a tag on the furnace and the gas supply has been shut off.
  • Water is standing at the base of the furnace, or the flue outside has iced over.
The license
Held by the contractor, not by this site, and issued where the work happens — New Hampshire licenses at state level, at city level or not at all depending on the trade and the town. Ask for the number and the name it is held under: a trading name and the licensed entity are often not the same.
The figure
Set by the contractor and said before the work starts. This site never quotes and has no part in it. If a technician cannot say what the visit covers before beginning, that is the moment to stop.
The call
Describing what the system is doing commits you to nothing. Nothing is booked until you say so.

What the visit involves

  1. 01

    The diagnosis

    At the thermostat first, then at the furnace or the condenser, in the order the equipment runs. What the system is doing is established before any part is named.

  2. 02

    The finding, out loud

    What failed, whether it is the fault or a symptom of another one, and whether the repair suits the age of the system. A diagnostic visit is usually charged separately from the repair — ask whether it is credited if the work goes ahead, because that differs from one contractor to the next.

  3. 03

    The repair

    Agreed with the contractor before it starts. Where a part has to be ordered, a technician says so rather than leaving the system apart.

Before you call: what to have ready

  1. 01Which system it is: a furnace, a boiler with radiators or baseboard, or a heat pump with electric backup.
  2. 02The two thermostat numbers: the setting, and the reading it shows for the room — and whether the screen is blank, because a thermostat wired without a common wire runs off its battery, and a battery that has gone down looks exactly like a dead furnace.
  3. 03Whether the gas utility has already sent someone, and whether anything has been tagged.

Do not keep pressing the reset while you wait — each press relights a furnace that shut itself down for a reason, and the lockout it is holding is the first thing a technician reads.

Heating Repair in Antrim: questions

How many freezing days does Antrim have?

Antrim averages 172 days a year with a low of 32°F or colder and 84 at 20°F or colder, by the 1991–2020 climate normals for a NOAA station 10 miles away. Heating is the main system here, and a furnace that quits in January is an emergency rather than an inconvenience.

When were most houses in Antrim built?

Half the homes in Antrim were built before 1938, by the Census Bureau's 2019–2023 American Community Survey. Detached houses make up most of the housing. In houses that age the furnace or air conditioner has usually been replaced at least once, and the ducts and the flue are often older than the equipment.

How efficient must a new gas furnace be?

The federal minimum for a new non-weatherized gas furnace is an AFUE of 80. A 95 standard is set for furnaces made after December 18, 2028 and is still in court, so a furnace going in now can be an 80 or a condensing model in the 90s.

Map loads when you reach it

Other services in Antrim

Heating Repair nearby

Call (888) 217-3739